Master Catalog — Gems Sensors & Controls - E-32

Solutions in a Box:
Application-Specific Kits
Bring Simplicity to Systems Engineering
 Time Savers
 No Component Selection Hassles
 Compatible Components
 Little or No Assembly
If you need to automatically refill or drain tanks, wells or pressurized vessels, these
convenient pre-packaged kits contain everything you need. These Warrick® level
control kits combine all the know-how and components you'll need to add automatic
control to pump-up/pump-down operations. Each kit is supplied with controllers,
probes, electrical enclosures and full instructions.

TK-1 shown

TK Kits - Refill or Drain Open Tanks

TK-2 Kits are designed for the opposite application-controlling the drain pump in
open tanks and ponds that fill regularly. It turns the pump ON when the liquid level
rises to a point and turns it OFF when the level drops back to a point.

WK Kits - Refill or Drain Wells
WK Kits are designed for use in wells. WK-1 Kits control refill in wells that drain
regularly; WK-2 Kits control the pump-down in wells that fill regularly. Minimal
assembly is required. WK Kits can also be used for low-water cutoff applications.

WK-1 shown

Length of suspension wire is 50 feet. Additional suspension wire (3Z1A) is available
from your local Warrick Controls Stocking Representative or Distributor.

HP Kits - Refill or Drain Pressure Vessels
HP-1 Kits are designed to automatically control the refill pump in up to 125 psi
pressure vessels that drain regularly, turning the pump ON when the liquid level in
the vessel drops to a low point and turning it OFF when the level rises back to a high
point. Minimal assembly is required. Also for low-pressure sealed vessels.
HP-2 Kits are designed for the opposite application-controlling the drain pump in
pressure vessels that fill regularly. It turns the pump ON when the liquid level rises to
a high point and turns it OFF when the level drops back to a certain point.

HP-2 shown

WARRICK CONDUCTIVITY SENSORS

TK-1 Kits are designed to automatically control the refill pump in open tanks and
ponds that drain regularly, turning the pump ON when the liquid level in the tank
drops to a point and turning it OFF when the level rises back to a second point.
No assembly is required, just connect wire to control.

How To Order
Select Part Number based on application. Each kit contains everything needed for
specified application: control, fitting, probes, electrical enclosure, and instructions.
Part
No.

Application

TK-1

Tank refill

TK-2

Tank drain

Primary
Voltage
115 VAC

WK-1 Well or sump refill 115 VAC or
WK-2 Well or sump drain 230 VAC
HP-1

Tank refill

HP-2

Tank drain

Warrick Kits / p1of1 / 3-APR-14

Secondary
Sensitivity
Voltage

115 VAC

12 VAC

Contact Rating

Mode of
Operation

26K

10 amp Resistive
1/3 hp

Inverse

19K

30 amp Resistive
1 hp @ 115VAC or
2 hp @ 240 VAC

Inverse

10 amp Resistive
1/3 hp

Inverse

26K

Direct
Direct
Direct

Visit www.GemsSensors.com for most current information.

E-32

http://ecatalog.gemssensors.com/ecatalog/warrick-panels-and-kits/en/TK1 http://ecatalog.gemssensors.com/ecatalog/warrick-panels-and-kits/en/TK2 http://ecatalog.gemssensors.com/ecatalog/warrick-panels-and-kits/en/WK1 http://ecatalog.gemssensors.com/ecatalog/warrick-panels-and-kits/en/WK2 http://ecatalog.gemssensors.com/ecatalog/warrick-panels-and-kits/en/HP1 http://ecatalog.gemssensors.com/ecatalog/warrick-panels-and-kits/en/HP2 http://www.GemsSensors.com

Master Catalog — Gems Sensors & Controls

Table of Contents for the Digital Edition of Master Catalog — Gems Sensors & Controls