Microwave Engineering Europe - October 2008 - (Page 44)

44 PRODUCTS Agilent offers a new approach to nonlinear component characterization using X-parameters In RF applications, ampliﬁers are considered an indispensable component and yet due to their nonlinear behavior, are often the cause of wasted frequency spectrum. Designing a power ampliﬁer to operate only within its region of linear operation also results in an inefﬁcient use of the available power. Ampliﬁers are often driven into the nonlinear region of operation and then linearized around that point. Consequently, it has become increasingly important to understand the nonlinear behaviors of active RF components such as power ampliﬁers and frequency doublers which, in turn, makes accurate measurement of a device’s nonlinear behavior all the more crucial. Unfortunately, making nonlinear measurements is not an easy task, especially considering that currently available tools and models are generally difﬁcult to use and do not provide the information required. Measuring nonlinear effects Agilent is introducing two primary methods for measuring the nonlinear effects of a device under test (DUT): nonlinear component characterization and X-parameters. Nonlinear component characterization provides calibrated, vectorcorrected waveforms of the incident, transmitted and reﬂected waves from the DUT. Vector calibration, power calibration and the use of a poly-harmonic phase reference and calibration removes the systematic error terms. With this measurement, all receivers must be measured simultaneously for each frequency point. The information derived from nonlinear component characterization measurements enables the engineer to measurement capability of the PNA-X for linear measurements. It can then easily switch into the NVNA mode for nonlinear measurement. The NVNA’s method of measuring nonlinear component behavior through the use of nonlinear scattering parameters or X-parameters provides an accurate portrayal of both nonlinear device and cascaded nonlinear device behavior using measurement-based data. Additionally, the X-parameters can be accurately cascaded from individual devices using the company’s ADS to simulate and design more complex modules and systems. These parameters separate out a critical term from the measurement, XT, which enables accurate nonlinear design and simulation by taking cross-frequency mismatch properly into account for nonlinear components. Conclusion Accurately measuring and reducing a device’s nonlinear behavior is crucial to creating linear high-power solutions for use in a range of applications in aerospace and defense and telecommunications, just to name a few. While conventional solutions to this challenge fail to provide the information and accuracy required, NVNA software uses component characterization and X-parameters to quickly, easily and with the highest degree of accuracy measure nonlinear behavior in a DUT. With its full match correction and accurate amplitude, as well as cross-frequency relative phase information, the NVNA is today providing a new standard in accuracy and insight into the behaviors of nonlinear components. EuMW 2008 Exhibitor: Stand 703 www.mwee.com/210700066 better understand and more deterministically control the nonlinear behavior of the DUT. On the other hand, Xparameters are the logical, mathematically-correct extension of S-parameters into a nonlinear, large-signal operating environment. X-parameters are to nonlinear measurements what S-parameters are to linear measurements. X-parameter measurements require an additional source which is used to drive the DUT with both a large and small signal tone at the appropriate frequencies and phases, at the same time. Careful control of the phase and amplitude of these signals is therefore critical. Measuring the amplitudes and phases of the scattered waves under these conditions allows for the identiﬁcation of Xparameters. These parameters provide the engineer with information on such things as device gain and match, while the device is operating in either a linear or nonlinear state. The X-parameters can be extracted into Agilent’s Advanced Design System (ADS) or displayed like S-parameters. Because the X-parameters relate cross-frequency dependencies, there are usually many more X-parameters than S-parameters, such as in the case of the gain of the output fundamental frequency to the input third harmonic. Here, there are eight X-parameters for this simple case with only one harmonic and no power dependency. In contrast, there can never be more than four S-parameters. X-parameters also depend explicitly on the large signal state of the device, making input power a variable. In contrast, S-parameters are assumed to be power independent. Nonlinear vector network analyser Utilizing a solution that employs both nonlinear component characterization and Xparameters provides critical insight, essential to accurately measuring a device’s nonlinear behavior. Agilent Technologies’ Nonlinear Vector Network Analyzer (NVNA), shown in the picture, supports both methods in a highly integrated, powerful and simple to use instrument. With a minimum amount of external hardware, this solution effectively converts a 4-port PNA-X microwave network analyzer into a highperformance nonlinear analyzer from 10 MHz to 26.5 GHz. Because the NVNA is based on a standard PNA-X microwave network analyzer, it provides all the power, ﬂexibility and Microwave Engineering Europe ● October 2008 ● www.mwee.com 044_MWEEnew.indd 44 6/10/08 12:46:27 http://www.mwee.com/210700066 http://www.mwee.com

Table of Contents Feed for the Digital Edition of Microwave Engineering Europe - October 2008

Microwave Engineering Europe - October 2008 Contents Comment News Cover Feature: AWR's AXIEM Software Brings 3D Planar Electromagnetic (EM) Simulation "Up Front" RFID: Augmented Reality: Beyond RFID and QR Codes for Mobile Phone Platforms Filters & Frequency Synthesis ZigBee Goes Green with Support for Smart Energy Simplify Mobile Data Applications and Services Test Enabling the State-of-the-Art in Automatic Test Equipment National Physical Laboratory Test Facility Aids Development of Next-Generation Antennas Selecting the Synthetic Test Environment for Transmit-Receive (T-R) Modules in a Phased Array Radar System Products Calendar

Microwave Engineering Europe - October 2008

For optimal viewing of this digital publication, please enable JavaScript and then refresh the page. If you would like to try to load the digital publication without using Flash Player detection, please click here.