StandOffs - (Page 22) Fixed Hinges StandOffs How To: StandOffs with Plexiglass & Glass Web Site Link (Parts include everything shown unless otherwise noted) NOTE: Hinges lock into place and are not meant to be moving parts. All StandOff Fixed Hinges are available in CLEAR and BLACK anodized finish. Black anodize available at additional cost. 1-11/16" 13/16" 13/16" StandOffs 1" Diameter Fixed Hinge 1" SO-A1H 5/16-18 tapped holes. Part SO-A1H Diameter 1" Thickness 5/16" Round Caps 60° Min 1" Fixed Hinge & Cap (Specify panel thickness when ordering) SO-A1H/CAP 9 Imagine the possibilities! Geometric Caps Part SO-A1H/CAP 9 Diameter 1" Cap Height 3/8" Measure and mark the hole centerline. Low Proile Caps 60° Min 1" Fixed Hinge & Edge Grip w/Disc Cap (Specify panel thickness when ordering) SO-A1H/EGC125 Thru EGC500 SO-DISC 2 Part SO-A1H/EGC125 SO-A1H/EGC250 SO-A1H/EGC375 SO-A1H/EGC500 Diameter 1" 1" 1" 1" Holds 1/8" 1/4" 3/8" 1/2" Carefully drill a 3/8" hole using a plex bit. Security Caps 60° Min 1" Fixed Hinges & Edge Grip w/ Threaded Cap (Specify panel thickness when ordering) Barrels SO-A1H/EGTC125/15 Thru EGTC500/15 SO-CAP 15 Part SO-A1H/EGTC125/15 SO-A1H/EGTC250/15 SO-A1H/EGTC250/15 SO-A1H/EGTC500/15 Diameter 1" 1" 1" 1" Holds 1/8" 1/4" 3/8" 1/2" Hubs 2-5/8" 1-5/16" 1-5/16" 1-1/4" Diameter Fixed Hinge 1-1/4" When using glass, have your glass shop drill a 1/2" hole then use 7/16" plastic tubing inside the hole and vinyl washers between glass and Hinge to protect the glass. These parts are found in the Hardware Catalog on Pg. 175. Links & Travelers SO-A125H 5/16-18 tapped holes. Part SO-A125H Diameter 1-1/4" Thickness 3/8" StandOff Hinges make attractive accents. Grippers 60° Min 1-1/4" Fixed Hinge & Cap For Cap specs, see page 5. (Specify panel thickness when ordering) Edge Grips SO-A125H/CAP 1 Thru CAP 3 Part SO-A125H/CAP 1 SO-A125H/CAP 2 SO-A125H/CAP 3 Diameter Cap Height 1-1/4" 1-1/4" 1-1/4" 1/2" 3/8" 1/2" Fixed Hinges SO-DISC 1 The addition of a Link (pg17), allows Fixed Hinges to turn to the inside at 90˚. SO-CAP 16 SO-AEGHD Part 1-1/4" Fixed Hinge & Adjustable Edge Grip For Edge Grip specs, see page 21. Diameter 1-1/4" 1-1/4" Holds 1/4"-1/2" 1/4"-1/2" SO-AEGHD SO-AEGH/16 Tighten set screw when hinge is at the desired angle. Hinges can be used in a variety of configurations. Note: Hinges lock into place and are not intended to be used as moving parts. SO-AEGH/16 SO 22 Note: To increase the amount of available hinge travel see Links on page 17 SO 23 http://www.standoffsystems.com
For optimal viewing of this digital publication, please enable JavaScript and then refresh the page. If you would like to try to load the digital publication without using Flash Player detection, please click here.