Rely On Us - October 2016 - 18

Crown Cutters H4 MC Crown Cutter | H4MC H4MC - the crown cutter for metal and ceramics 700 for use: Recommendations Indications Product characteristics and and black rings (white for ceramics, Material reduction accumulated (mg) low fusionall ceramics. Designed forofcutting commonly used metal alloys, titanium and 600 veneers made of low fusion ceramics. * Optimal speed:500 (160.000 rpm The H4MC can be identified by its white 1 in the micromotor. 400 90 80 70 60 50 advantages 40 300 Due to its special D-toothing, the H4MC facilitates quick and efficient * In case of materials that tend tocutting of 30 200 crowns bridges made of conventional metal"jump", alloys. Large spaces allow (e.g. certainchip non-precious Crowns should be cut in several steps,and 20 Recommendations for use: Indications Due towhen its special D-toothing, thewith H4MC 100 chip removal cutting soft alloys goldalloys), content. metal we recommend the i.e. the procedure is carriedquick out in intervals 10 * Optimal speed: (160.000 rpm The H4MC can be identified by its white 1 0 applying low 0 quick and efficient cutting ofuse inin thethemicromotor. turbine, in order to cut only a small area and blackfacilitates rings (white for ceramics, 30 s 60s 90 s 120 s 150 s 180 s 210s 240 s 270s 300s metal). The H4MCblack is forequally suited for ceramic veneers. The tiptransversing blade allows time contact pressure. each time. 2 crowns and bridges made of conventional * In case of materials that tend to H4MCL -prevents material reduction accumulated "jump", (e.g. certain non-precious Crowns should into be cut in several easy penetration thesteps, material. The pyramid shaped blade design blade metalis carried alloys. Large chip spaces allow quick metal alloys), we recommend the i.e. the procedure out in intervals Andere - capacity material reduction accumulated and increased stability and resistance tothe breakage, * In high order makeapplying full use Ceramic veneers should bebreakouts cut with use in to the turbine, low of in order toguarantees cut only a small area H4MCL - material reduction per time unit pressure. chip removal and prevent clogging, espe2 of thecontact instrument's working part ensuring it each is time. smooth with little vibration. the Tungsten Carbide crown cutter Andere - material reduction per time unit * In order make full use of the capacity Ceramic cially veneers should be cut with thetocutting phase, we recomH4MCL.314.012 (fig. 1). when cutting soft alloys with goldduring of the instrument's working part the Tungsten Carbide crown cutter mendduring to the apply the instrument at an Ceramic veneers are cut with H4MCL.314.012 (Fig 1) cutting phase, we recomH4MCL.314.012 (fig. 1). best content. The H4MC is equally suited for black for metal). apply the instrument an crown. anglemend of toapprox. 45° toatthe Metal crowns are to be cut with crown Metal crowns arebest to be cut with crownwith H4MCL.314.012 (Fig 2) Metal crowns are cut ceramic veneers. cutter H4MCL.314.012 (fig. 2). Compared to all other crown cutters on the angle of approx. 45° to the crown. cutter H4MCL.314.012 (fig. 2). Pack of 5 market, copies made by the competi* Always make sure thatincl. sufficient coolant To cut zirconia, please use 4ZR.314.012 is applied (at least 50 ml/min.). is applied (at leastthe 50 ml/min.). tion, H4MC (working part comes in varA further distinctive feature is the tiptrans* Do not exceed a maximum contact * Always make sure that sufficient coolant $85 versing blade permitting easy penetration ious lengths, see reverse: H4MC - pressure of 2N. * Do not exceed a maximum contact features a consistently higher into the material to be cut. The pyramidpressure ofH4MCXXL) 2N. material reduction rate. These cutters shaped blade design prevents blade breakouts and guarantees increased stability and high resistance to breakage, H4MC.314.010 prove particularly efficient in case of hard- H4MC.314.012 to-cut non-precious metal alloys such as H4MCL.314.010 thus ensuring a smooth operation with little Dentitan. The instruments can be used in H4MCL.314.012 H4MC.314.010 the micromotor vibration. H4MCXL.314.014 as well as in the turbine. ca. 45° H4MCXXL.314.014 H4MC.314.012 8,0 mm 7,0 mm 6,0 mm 5,0 mm These crown cutters are not H4MCL.314.010 suited for cutting all-ceramic crowns and bridge frames made of extremely hard ceramics, such as 4,0 mm 3,5 mm 3,0 mm H4MCL.314.012 zirconiumoxide ceramics. For this, we recommend the crown cutter 4ZR.314.012 specially developed 2,0 mm for zirconium oxide. H4MCXL.314.014 0 mm H 4 MCXXL H 4 MCXL 8,0 mm H 4 MCL 4ZR.314.012 H4MCXXL.314.014 H4 MC © 06/2015 · 417074V0 1,0 mm ca. 45° Henry Schein Halas · 44 O'Dea Avenue · Waterloo NSW 2017 · Ph 1300 65 88 22 · Fax 1300 65 88 10 · info@henryschein.com.au · www.henryschein.com.au 7,0 mm These crown cutters are not 417074V0_PI_EN_H4MC-H4MCL_Halas.indd 2 6,0 mm 02.06.15 14:01 suited for cutting all-ceramic crowns and bridge frames made of 5,0 mm extremely hard ceramics, such as 417074V0_PI_EN_H4MC-H4MCL_Halas.indd 1 4,0 mm zirconiumoxide ceramics. For this, 3,5 mm we recommend the crown cutter 3,0 mm 18 4ZR.314.012 specially developed 2,0 mm O C T O B E R 2 0 1 6 w w for w zirconium . h e noxide. ry sc he i n.c om.a u Material reduction per time unit (mg) The new H4MC - considerably higher material reduction and increased service life Designed for cutting all commonly used For Metal and Ceramics metal alloys, titanium and veneers made http://henryschein.com.au

Table of Contents for the Digital Edition of Rely On Us - October 2016