Krylon Canadian Product Guide 2008 - English - (Page 23) EPOXIES Surface Tolerant High Build Epoxy Mastic Surface Tolerant High Build Epoxy Mastic is a high build, high solids, polyamide epoxy. It is designed to protect steel and concrete in industrial environments. • COV: 260 g/L (2.2 lb/gal) • Fast drying • High solids content ensures adequate protection of sharp edges, corners and welds • Can be applied directly to marginally prepared steel surfaces Recommended Uses: For use over prepared steel and concrete in industrial exposures such as fabrication shops, refineries, pulp and paper mills, chemical plants, power plants, tank exteriors, offshore platforms, water treatment plants, marine applications and concrete floors COLOURS* 3.78 L cans Haze Grey K06860100-16 Black K06860113-16 White K06860404-16 BASES White K06867250-16 Deep K06867252-16 Clear K06867253-16 Hardeners For Deep Base Only K06863333-16 For All Others K06864444-16 1 to 1 mix ratio–Paint to Hardener 18.9 L pails K06860404-20 K06867250-20 Multi-Purpose Epoxy Multi-Purpose Epoxy is a modified epoxy phenalkamine, formulated specifically for immersion and atmospheric service in industrial and marine environments. • COV: 274 g/L (2.3 lb/gal) • Can be applied at temperatures as low as 18°C • Provides exceptional performance in corrosive environments • Surface tolerant - damp surfaces • Chemical resistant • Acceptable for use in federally inspected meat and poultry plants Recommended Uses: For use over prepared steel and masonry surfaces including structural steel, fabrication and new construction, water and wastewater treatment facilities, decks and superstructures, secondary containment, salt water and fresh water immersion service (non potable), offshore and marine structures, crude oil storage tanks, above- and below-water hull areas, ballast tanks, bilges and wet void areas, suitable for use with cathodic protection systems COLOURS* White Buff Haze Grey Hardener 946 mL can 3.78 L in a 3.78 L can K03900404-16 K03900050-16 K03900100-16 15 L in a 18.9 L pail K03900404-19 K03900100-19 K06864444-20 Coal Tar Epoxy Coal Tar Epoxy is a high build, polyamide cured epoxy coal tar coating. • COV: 306 g/L (2.55 lb/gal) • Can be applied at a high film thickness in one coat Recommended Uses: For use over prepared steel and concrete in industrial exposures, such as petroleum storage tanks, as a liner for clarifiers, dam gates, non-potable water tanks, offshore drilling rigs, marine applications, penstocks and as a heavy-duty structural coating COLOURS* 3.78 L can Black (Part A) Hardener (Part B) K02008430-16 3 to 1 mix ratio–Paint to Hardener 11.4 L in a 18.9 L pail K02000113-30 * For Colour Selections, see Pages 38-40. Can be tinted using Color-On-Demand. See Page 41 for details. K03904444-14 K03904444-16 4 to 1 mix ratio–Paint to Hardener 23 CUSTOMER SERVICE Phone: 866-736-1486 Fax: 800-243-3075 www.KPG-Industrial.com http://www.kpg-industrial.com/products/surface_tolerant_high_build_epoxy_mastic_k0686_series/ http://www.kpg-industrial.com/products/multipurpose_epoxy_k0390_series/ http://www.kpg-industrial.com/products/coal_tar_epoxy/ http://www.kpg-industrial.com/products/coal_tar_epoxy/ http://www.kpg-industrial.com/products/surface_tolerant_high_build_epoxy_mastic_k0686_series/ http://www.kpg-industrial.com/products/multipurpose_epoxy_k0390_series/ http://www.kpg-industrial.com/products/coal_tar_epoxy/ http://www.KPG-Industrial.com
For optimal viewing of this digital publication, please enable JavaScript and then refresh the page. If you would like to try to load the digital publication without using Flash Player detection, please click here.