EQ Magazine - January 2008 - (Page 48)

DRUM HEADS 7 COMMON PITFALLS OF RECORDING DRUMS by Jake Wood The last thing an engineer wants at a session is an overprotective drummer hovering over his shoulder, making passive-aggressive mixing suggestions. But look at it from the drummer’s perspective: One of the most frustrating situations he or she deals with is the loss of control over the drum tones on a recording. While there is always room for interpretation of what a drum set should sound like, if the mix doesn’t sound good to the drummer, then maybe something wasn’t done right. Most drummers really take care to find the tones they want, and they want them represented accurately in the mix. The drum sound should be just as inspirational as the performance—one part wood, one part snap and pop, and one part magic. Here are some common ways that engineers can destroy your groove. UNDERBELLY UGLINESS Some engineers mic the top and bottom of the snare, but the best mixes use the bottom signal solely as a reserve source for additional attack. Keep in mind that nobody actually hears the drums from the perspective of the bottom snare mic, so it should not be prominent in the mix. Turn that bottom mic up, and two problems arise: The warm and wooden tone gets buried, and every snare hit starts to sound like paper (which serves to give ghost notes a new and undesirable characteristic). Add that bottom mic with caution, and remember that one well-placed mic is more valuable than three poorly-placed mics. GAGGED SNARES While there is a time and place for both harsh, ringing snares (as on any Soul Coughing album) and dead, cardboard-box snares (as on Neil Young’s Harvest), many engineers are terrified by ring. Now, while it may be a safer route to record a muted snare, the annoying ring that drives engineers up the wall is actually a vital element of the snare tone. Try and work with the ring rather than killing the tone with duct tape. background, it’s also important to capture accurate volume levels of the individual drums as the drummer plays them. The drummer plays something hard or soft for a reason, and when a part of the kit is turned up or down, the blend can start to sound lopsided. Just imagine what would have happened if someone cranked Stewart Copeland’s kick and snare, and buried his genius hi-hat work on those classic Police hits. OVER-COMPRESSION Many engineers binge on compressors. While compression can certainly fatten up the tone, over-compressing can cause the loss—or over-amplification—of ghost notes, which alters the drum performance. This is bad. And if you haven’t matched the release setting of the compressor to the song tempo, you’ll likely have sustained tones and decays stepping all over the groove. A little compression goes a long way if you want a natural and organic drum performance that captures the player’s dynamics and tone. TRIGGERING SAMPLES Replacing natural drum sounds with samples can be much like a breast implant that’s a few sizes too big. It might sound good at first, but, ultimately, it can easily become cheap and tacky. CONTROLLING THE CONTROL ROOM Making a record takes cooperation, but some engineers think the control room is their place to be in total control of the tonal landscape. It should really be called the “listening room, and everyone should be able ” to share ideas and be heard. Above all, everyone should be listening critically to the tracks, and seeking ways to make all the instruments and voices sound wonderful in the context of the musical work. A good engineer with sonic defaults and a god complex can absolutely craft a good, conventional drum sound. However, a great engineer who really listens—and who seeks to manifest the sounds the musicians hear in their heads—can improvise around stylistic and tonal idiosyncracies to deliver magic. Jake Wood in action. STYLISTIC IGNORANCE A typical jazz kit and a typical rock kit are drastically different in how they produce tone, dynamics, and attack. Engineers who only listen to rock should do some homework if they have a jazz session coming up, and vice versa. Jazz drumming doesn’t sound too good when it’s played on a rock kit, and it won’t sound good if it’s recorded and mixed like a rock kit, either. Sadly, many home and studio engineers default to the same methodology no matter what kit—or what type of player—they are recording. Before you dive in and destroy the nuances of a jazz kit, or neuter the attack of a rock kit, listen to the sound of the drums in the room. You should also reference good recordings in the appropriate style. Then, set up the mics to best capture the tone in front of you, rather than the tone your assumptions and biases are playing in your head. REMIXING Drummers are very aware that timbre wiil change depending on the force they use to strike a drum, and, as a result, they become their own four-limbed mixing machines. While it’s common practice to boost the kick and snare, and keep the other drums in the 48 EQ JANUARY 2008 www.eqmag.com http://www.eqmag.com

Table of Contents Feed for the Digital Edition of EQ Magazine - January 2008

EQ Magazine - January 2008 Contents Talk Box Sounding Board Robbers On High Street Rafter RTX Sharon Jones and the Dap-Kings Toolbox Rahim Dimmu Borgir Wu-Tang Clan Special Feature! Mastering for Musicians Guitar Trax Bass Management Key Issues Drumheads Vocal Cords Mix Bus Cheat Sheet Cakewalk Sonar 7 IK Multimedia Virtual Instruments Yamaha MSP7 Shure KSM137/SL K+H O 300 & O 800 Sonica Livetracker Apple Logic Studio Novation XioSynth 25, Audio-Technica ATH-M50, Samson G-Track

EQ Magazine - January 2008

For optimal viewing of this digital publication, please enable JavaScript and then refresh the page. If you would like to try to load the digital publication without using Flash Player detection, please click here.