Tech Directions - February 2009 - (Page 19) Does It Work? 555-Timer Checker Leaves No Doubt By Charles Harman charman@sbcglobal.net N an earlier article, I provided instructions on making and using an op-amp checker (Tech Directions, December 2007). This article details construction and use of another type of IC chip tester: the 555-timer checker. Whether you are a student or an instructor, having the means to check the operation of a 555-timer is very useful. Most students do not have the experience or knowledge that it takes to recognize whether a 555-timer circuit is operating normally or not. With this 555-timer checker, a student or an instructor can simply remove a 555-timer from a proto-board, insert the questionable component into the 555-timer checker’s test-socket (TIMER), push the press-to-test button (PTT), and see if the 555-timer checker’s LEDs (light-emitting diodes) are toggling. It’s that simple. I How It Works The 555-timer checker allows the user to dynamically check a 555-timer, an integrated circuit (IC) device. Introduced by the Signetics Corporation about 37 years ago, the 555-timer is an oldie but goodie. Of its many applications, it provides timing applications that unijunction transistors (UJTs) once performed. It was then, and is now, an industry standard. Charles Harman taught electronics at ITT Technical Institute in both Houston and Garland, TX, before retiring. He is currently a proctor for the Electronics Technician Association. The 555-timer is an integrated circuit chip that contains the active elements of a RC oscillator with a discharge BJT, two comparators, and an RS flip-flop. It is packaged in an 8-pin dual-inline-package (DIP), an 8-pin round-can package (TO99), a 14-pin DIP (two timers), and several surface-mount package styles. It is a very important building block in the electronics industry. It can be hooked up as an astable (freerunning) oscillator producing a periodic rectangular wave or as a monostable (one-shot) generator producing a single rectangular pulse with a finite pulse width. The output of a 555-timer can either sink or source a load. It is a very versatile IC building block. The 555-timer checker’s circuit is wired as an astable multivibrator without a 555timer IC. When the user inserts a good 555-timer into the 8-pin DIP socket, the 555-timer’s output drives a pair of LEDs and their series, current limiting, resistors. A 9 V battery powers the 555-timer checker’s circuit so as to produce a positive-going square-wave output. When the output wave of the-555timer goes positive, the right LED (Vhi) glows and when the output wave is at ground potential, the left LED (Vlo) glows. When the right LED glows, the 555-timer is in the source mode. When the left LED glows, the 555-timer is in the sink mode. Our 555-timer checker can only check 555-timers packaged in the 8-pin DIP or the 8-pin round can (TO99) package. They are the most popular IC packages used by students enrolled in technical schools’ analog and/or digital classes. Procedure I suggest that you first build the 555-timer checker circuit on your proto-board so it resembles the 555timer checker shown in Photo 1. This Photo 1 will allow you to see and physically hook up all necessary components in the circuit, as well as better understand the theory of operation of the 555-timer checker. Refer to the schematic diagram as you build your circuit. For the most part, all parts needed to build the 555-timer checker are available at Radio Shack and are listed on the parts list. At this stage of the project, you will not need an 8-pin socket or the plastic enclosure. After you have successfully built your 555-timer checker on your proto-board, tested it, and proven it www.techdirections.com ELECTRONICS 19 http://www.nxtbook.com/nxtbooks/prakken/techdirections1207/index.php?startid=Cover1 http://www.nxtbook.com/nxtbooks/prakken/techdirections1207/index.php?startid=Cover1 http://www.techdirections.com
For optimal viewing of this digital publication, please enable JavaScript and then refresh the page. If you would like to try to load the digital publication without using Flash Player detection, please click here.