Plant Services - June 2008 - (Page 19)

WHAT WORKS Polyurethane takes on damp pipes Moisture-cured coating renews protection of water filtration facility hen maintenance was required inside the Hammond Water Filtration Plant in Hammond, Ind., more than 35,000 square feet of piping and valves were coated with a moisture-cured polyurethane system. The plant, which was built in 1936 and renovated in 1950 and 1970, posed numerous repainting challenges. Some of the pipes had never been coated, producing serious corrosion problems. There were no coating records, but it was likely that lead was present. It was imperative to remove the rust and any lead-based paint before any recoating, but cold water piped into the plant caused significant condensation, making coating extremely difficult. In October 2004, Hammond called upon Dixon Engineering (www.dixonengineering.net) to evaluate the project and make recommendations. Ira Gabin, vice president for Dixon, says, “Performance and aesthetics were the major considerations – they wanted the job to last and look good 15 to 20 years from now. It was a huge project, and it was going to take a really experienced coatings contractor. The crew would be limited to working in winter months when pipe sweating is minimal. In late spring and summer, you’d get huge differentials in water temperature, and it would be like walking through a waterfall in there.” Dixon Engineering specified a moisture-cured urethane (MCU) system formulated from raw materials manufactured by Bayer MaterialScience LLC (www.bayer materialsciencenafta.com). They called on SherwinWilliams (www.sherwin-williams.com), which agreed to deliver the paint within a week’s time. The SherwinWilliams system consisted of two different Corothane primers to be used on two types of pipes, plus an intermediate coat of Corothane I IronOx B, and a Corothane I aliphatic topcoat. Given the conditions inside the plant, Gabin noted, “The MCU system opened a bigger painting window for us.” In January, 2005, Era Valdivia Contractors, Chicago, was awarded the job. Project Manager Greg Bairaktaris says, “We walked this plant twice just to make sure we were comfortable with the logistical challenges. The bottom line was going to be proper planning and execution.” Work was scheduled to be completed in two phases so it could be performed in the cooler months. Era Valdivia June 2008 W The pipes would sweat, especially in the warmer months, so moisture-cured urethane primers were specified. began Phase I in March 2005. Plant Superintendent Gary Williams admits he was nervous about protecting valves, controls and other vulnerable equipment. Greg Bairaktaris notes that the surface preparation was particularly challenging. Dehumidification was necessary to remove condensation from the pipes to hold the blast. If dehumidification was not used, flash rusting would have occurred. The substrate was mostly steel, to be blasted to SP10 specification before it was coated with Corothane I GalvaPak. Cast iron pipes were prepped to SP6, then coated with Corothane I MIO Zinc. The moisture-cured Corothane system compensated for some of the on-site problems, because it could be applied to damp pipes and could handle some flash rusting. “It was hard to get the surface clean enough and moisture-free,” Bairaktaris says. “You couldn’t get that cast iron to near-white. But the moisture-cured system solves problems on the engineering side, as well as on the application side.” Once the primer was applied, the intermediate and topcoats followed. Since all the pipes needed to be color-coded, the topcoats were made with six pigments. And because the Corothane I aliphatic topcoat emitted a low (3.5) VOC, the plant could remain in operation even during the final stages of the maintenance project. Era Valdivia completed one room at a time during Phase I, before tackling Phase II in January 2006. Both phases were completed on time. In all, the project spanned two years and took 900 gallons of coating. “We’re very happy with the way it turned out,” Williams says. 19 www.PLANTSERVICES.com http://www.dixonengineering.net http://www.bayermaterialsciencenafta.com http://www.bayermaterialsciencenafta.com http://www.sherwin-williams.com http://www.PLANTSERVICES.com

Table of Contents Feed for the Digital Edition of Plant Services - June 2008

Plant Services - June 2008 Contents From the Editor Letters The PS Files Up and Running Crisis Corner What Works Asset Manager Technology Toolbox Cover Story HVAC Coatings Motors Web Hunter In the Trenches Product Picks Classifieds Energy Expert

Plant Services - June 2008

For optimal viewing of this digital publication, please enable JavaScript and then refresh the page. If you would like to try to load the digital publication without using Flash Player detection, please click here.