IEN - January 2009 - (Page 10)

IEN / JANUARY ’09 pAgE 10 80 in. high hardness of 82 Shore D Mobile Wire Shelving Structural Methacrylate Adhesive with mixed viscos- has red, yellow, or blue polypropylene Quantum shelf bins with reinforced side ribs, wide hopper fronts, and slotted label holders for product identification. Used to move ity of 22,000 cP is formulated to produce clear bond line on various plastics. Clear Welder requires little or no surface preparation and withstands service temperatures from -67 to 200°F. Available in 380 mL coaxial cartridges, 2-part adhesive is mixed as dispensed in 10:1 ratio with manual/pneumatic dispensing gun and attains functional cure in 2 hr at room temperature. ITW Devcon; 800-933-8266; Tech Contact: Brad Williams www.ieninfo.com/11222 -126 or circle 126 on card resists wear available in capacities of 75 ft of 3/4 in. ID hose and 50 ft of 1 in. ID hose. Reels include dual bearing axle support system that creates low friction, extraction, and retraction. Stainless steel rollers withstand extreme applications, and blue CPC powder coat finish provides chip and weather resistance. Coxreels; 800-269-7335 ext 119; Tech Contact: Florent Antonetti How To Change the Way You Spray Hose Reel in Truck Mount Series T is S parts and supplies to jobsite, units roll on four 5 in. polyurethane casters with nonmarking donut bumpers to protect walls and equipment. Eight adjustable chrome shelves support up to 800 lb. C&H Distributors, Inc.; 888-316-2223 www.ieninfo.com/11222 -123 or circle 123 on card www.ieninfo.com/11222 -127 or circle 127 on card standard & customizable 4-Fold Door Systems have High-Speed ALgorithm Drive Operator, which features fully programmable speed, acceleration, and deceleration as well as Collision Detection System. Integrated battery backup allows doors to operate in case of power failure. In less than 7 sec, F-Series door panels fold completely clear of opening and are visible by drivers during entire operation, eliminating damage to doors and vehicles. Doors are available in standard and custom sizes. Door Engineering & Mfg; 800-959-1352 507-931-6910 www.ieninfo.com/11222 -124 or circle 124 on card pray nozzles appear to be simple devices, but in service they function as highly precise instruments. When nozzles become partially blocked, spraying efficiency is degraded and your process can be compromised. The most frequent cause of clogging is the presence of contaminants in process water—a condition that is particularly common in systems that use recirculated water. Other factors that may cause clogging are particle agglomeration, scaling and bearding— the buildup of material on the inside and outer edges of the orifice. When positive displacement pumps are in use, clogged spray nozzles will increase process pressure, whereas flow will be most acutely affected when centrifugal pumps are used. If the spray application directly affects product quality, increased scrap is the inevitable result of nozzle clogging. This can happen when coatings, release agents, lubricants, or protective films are applied unevenly Spraying Systems Co.; 800-957-7729; Author and Tech Contact: Jon Barber . . . read the full article at www.ien.com/article/spray www.ieninfo.com/11222 -128 or circle 128 on card www.ieninfo.com/11222 -125 or circle 125 on card www.ieninfo.com/11222 -129 or circle 129 on card http://www.ieninfo.com/11222-126 http://www.ieninfo.com/11222-123 http://www.ieninfo.com/11222-126 http://www.ieninfo.com/11222-127 http://www.ieninfo.com/11222-128 http://www.ieninfo.com/11222-127 http://www.ieninfo.com/11222-123 http://www.ieninfo.com/11222-124 http://www.ieninfo.com/11222-128 http://www.ieninfo.com/11222-128 http://www.ieninfo.com/11222-124 http://www.ieninfo.com/11222-125 http://www.ieninfo.com/11222-129 http://www.ieninfo.com/11222-129 http://www.ieninfo.com/11222-125 http://www.ieninfo.com/11222-125 http://www.ieninfo.com/11222-129

Table of Contents Feed for the Digital Edition of IEN - January 2009

IEN - January 2009 Contents Hot New Products MRO/Plant Maintenance Problem Solvers Focus: CAD/CAM/CAE Free Catalogs & Tech Tips Plant Efficiency: Cost Cutters Free Samples Lifestyle Engineering Now on IEN.com Trade Show: ProMat 2009 IEN Best Brands Winners IEN’s WebReviews: Sensors Resource Center Advertiser Contact

IEN - January 2009

For optimal viewing of this digital publication, please enable JavaScript and then refresh the page. If you would like to try to load the digital publication without using Flash Player detection, please click here.