IEN - March 2009 - (Page 21) page 21 IeN / MaRCH ’09 Screwfeeder accommodates up to 11 Featuring fully adjustable rail system, precision screwfeeder can hold 1 to 5 mm screws. It feeds fasteners with less than 19 mm under head length and can also accommodate screws with captive washers. Adjustable bit guide in automatic feeder allows use of most standard bits. aSg Div, Jergens Inc: 216-486-6163. Tech Contact: Mike Starick www.ieninfo.com/11224 -277 or circle 277 on card different sized screws Extra-Large Stage Lift has moon-shaped, circular deck All-welded steel, circular stage lift relies upon 6 hydraulic cylinders for smooth and quiet operation. It measures more than 7 ft wide x 42 ft long and exceeds 10,000 lb in capacity. Cylinders are synchronized for uniform, level lifting by precision-built flow divider, and each cylinder is equipped with pilotoperated safety holding valve to prevent accidental lowering in case of power/hydraulic failure. Other sizes, lifting heights, and capacities are available. air Technical Industries: 888-857-6248 www.ieninfo.com/11224 -282 or circle 282 on card Flexible Beam Coupling with improved clamp design Machined from single piece of aluminum, zero-backlash beam couplings have both radial and cross cut to optimize surface contact with shaft. Multiple spiral cuts provide torsional stiffness and allow couplings to accommodate angular misalignment, parallel misalignment, and axial motion. Available in 20 body sizes, couplings have OD from 3/8 to 1-1/2 in. and bores from 3/32 to 3/4 in. Stainless steel models are also available. Ruland Mfg Co., Inc.: 508-485-1000. Tech Contact: Robert Watkins www.ieninfo.com/11224 -278 or circle 278 on card Fiber Optic Repeater with interference-free data transfer with 16-bit resolution Torque Sensor has USB output Including flange-to-flange mounting, Model TFF400 provides torque measurements from ±5 oz-in. to 500 lb-in., and torsional stiffness from 325 oz-in./radians to 199,000 lb-in./radians. Reaction torque sensor utilizes metal foil strain gauge technology and includes overload protection to help prevent damage during installation. Made of anodized aluminum, sensor operates from -60 to +200°F. FUTeK advanced Sensor Technology: 800-233-8835; 949-465-0900. Tech Contact: John Vargas www.ieninfo.com/11224 -279 or circle 279 on card Model 4154 HP with RS232 monitor port is used to regenerate data signals in order to extend range to greater than 1,640 ft between optically linked data terminals. It can also be used to monitor network traffic. Fiber optic communication standard allows data transmission unsusceptible to electrostatic/ electromagnetic fields. RS232 monitor port is protected from damage by potential differences. Fiber connections are via 2 standard Versatile Link connectors. electro Standards Laboratories: 877-943-1164; 401943-1164 ext 231. Tech Contact: Sandra Trahan www.ieninfo.com/11224 -283 or circle 283 on card Precison Ball Screw comes in left-handed thread style Linear Synchronous Motor for large machining centers Offering peak forces up to 13,000 N with dead weight of 45 g, Series IDAM L2U compensates for any magnetic forces generated between motors and magnets. By using iron-core linear ac synchronous motor with 2 symmetrically opposed secondary parts, units maintain accuracy and minimize friction-induced heat generation. Reduced iron content in movable primary component further minimizes mass in 3-phase motors. Schaeffler group USa, Inc.: 803-548-8500 www.ieninfo.com/11224 -280 or circle 280 on card Series BSL offers thread dia of 8, 10, 12, and 15 mm with corresponding leads of 2, 4, 5, and 10 mm. Ball screws are built from induction hardened and carburized steel in lengths from 100 to 895 mm, configurable in 1 mm increments. All are fully RoHS-compliant, and may be ordered with various key groove options as well as 3 grease options. Misumi USa, Inc.: 800-681-7402; 847-843-9105 ext 253. Tech Contact: Chris Blaszczyk www.ieninfo.com/11224 -284 or circle 284 on card Ethernet Radio enables continuous Models RAD-80211-XD/HP and RAD-80211XD/HP-BUS provide 400 mW (26 dBm) transmit power and 128-bit AES encryption. They allow secure wireless communica- data flow in mesh network Flowmeter withstands corrosion V-Cone Flowmeter provides flow measurement in liquid, steam, or gas media with accuracy of +0.5 and repeatability of +0.1. It operates over flow range of 10:1 in service line sizes from 0.5 to 120 in. Standard configurations may be specified with stainless steel or carbon steel materials. Flowmeter can also be constructed from other materials to meet specific requirements. McCrometer, Inc.: 800-220-2279; 951652-6811. Tech Contact: Gregg McCall www.ieninfo.com/11224 -281 or circle 281 on card www.ieninfo.com/11224 -286 or circle 286 on card in harsh processes tion over wireless mesh network of up to 40 radios. Radios conform to 802.11b/g standards, operate in 2.4 GHz band, and also support access point, client, and bridge/ repeater modes. Autobridge mesh mode enables network to self-form and heal if radio drops out. Built-in RS232 and RS422/485 device servers allow integration of serial devices. phoenix Contact: 800-888-7388; 717-944-1300 ext 3777. Tech Contact: Ira Sharp www.ieninfo.com/11224 -285 or circle 285 on card http://www.ieninfo.com/11224-282 http://www.ieninfo.com/11224-277 http://www.ieninfo.com/11224-277 http://www.ieninfo.com/11224-282 http://www.ieninfo.com/11224-278 http://www.ieninfo.com/11224-283 http://www.ieninfo.com/11224-278 http://www.ieninfo.com/11224-283 http://www.ieninfo.com/11224-284 http://www.ieninfo.com/11224-279 http://www.ieninfo.com/11224-284 http://www.ieninfo.com/11224-280 http://www.ieninfo.com/11224-285 http://www.ieninfo.com/11224-280 http://www.ieninfo.com/11224-281 http://www.ieninfo.com/11224-286 http://www.ieninfo.com/11224-285 http://www.ieninfo.com/11224-281 http://www.ieninfo.com/11224-286
For optimal viewing of this digital publication, please enable JavaScript and then refresh the page. If you would like to try to load the digital publication without using Flash Player detection, please click here.