JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 45

FEATURE “Marine” g…/… Development of operational monitoring sensors for the Veolia racing monohull Blue = front sensor (2 meters from the stem of the boat) Red = rear sensor (4 meters from the stem of the boat) Signal: Wave - contact period: 2,5 sec. Maximum level of deformation:?= 5.10-5 Maximum rate of deformation: d?/dt= 118%/s the impact is received at first at the front sensor but the maximum level is recorded on the rear the boat stem is out of the water and falls down to the bottom of the following wave the boat goes through a small wave and the front sensor shows scatterd variations. Fig. 5: Shear strain peaks from two sensors during sailing The shear strain values are relative to the zero of the data channels used in the measurements carried out on land. The load level remains negligible in relation to the foam’s maximum shear stress. However, nothing indicates that the sensors were where the greatest shear deformation occurred. The boat entering into contact with the waves produces shear strain peaks with a period of about 2.5 seconds. The waves have different shapes, which causes random maximum deformation peaks as shown by the readings below (Fig.5): The measurements also serve to locate the impact zones. In Figure a, the front sensor undergoes peak load before the rear sensor does. In Figure b, the opposite is true, and the load is lower than in scenario a. In Figure c, the type of stressing corresponds to a local impact in the bow, eliciting a random response from the sensors. The level of peak deformation is low during this measuring period, although the shear strain rate is 118 %/s. These results indicate that the mechanical characterization of the core materials used for structures of this kind should be done at high speed, whereas currently, only quasi-static tests are conducted. Conclusion The measurements at sea provided crucial information that served to make the boat more reliable and refine its settings. The information also suggests that a next step for future projects would be a characterization of the materials that is consistent with the strain rates encountered during sailing. Based on the results obtained and the analysis of them, the objective is now to instrument the boat in order to sail in the correct stress range, i.e. measure the main stress flows in order to be able to adapt sailing manoeuvres to limit extreme loads on the structure in dynamic and fatigue conditions. More information: http://www.canyousea.com http://www.univ-nantes.fr No35 September 2007 / JEC Composites Magazine
http://www.canyousea.com http://www.univ-nantes.fr http://www.diatex.com

JEC COMPOSITES MAGAZINE - Issue #35 - September 2007

Table of Contents for the Digital Edition of JEC COMPOSITES MAGAZINE - Issue #35 - September 2007

Edito
CONTENTS
NEWS WORLDWIDE
- Companies
- Agenda of events
- 2008 JEC Singapore
BUSINESS
- Market survey
- Niche markets
- Trends
- Human capital
FEATURE - MARINE
- Market
- Raw Materials
- Process
- Application
USERS’ PLATFORM
- Composites in the world
- Successful partners
- Applications
KNOW-HOW
- Warp knitting technology
- Testing
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 1
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 2
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - Edito
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 4
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 5
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - CONTENTS
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 7
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Companies
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 9
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Agenda of events
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 11
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - 2008 JEC Singapore
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 13
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 14
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 15
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Market survey
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 17
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 18
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 19
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 20
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 21
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 22
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 23
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Niche markets
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 25
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Trends
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 27
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 28
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 29
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Human capital
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 31
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Market
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 33
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Raw Materials
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 35
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 36
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 37
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 38
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 39
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Process
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 41
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 42
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 43
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 44
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 45
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 46
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 47
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Application
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 49
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Composites in the world
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Successful partners
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 52
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 53
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 54
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 55
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 56
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 57
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Warp knitting technology
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 59
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 60
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 61
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 62
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - - Testing
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 64
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 65
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 66
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 67
JEC COMPOSITES MAGAZINE - Issue #35 - September 2007 - 68
https://www.nxtbook.fr/newpress/jeccomposites/jcm2107_141
https://www.nxtbook.fr/newpress/jeccomposites/jcm2105_140
https://www.nxtbook.fr/newpress/jeccomposites/jcm2103_139
https://www.nxtbook.fr/newpress/jeccomposites/jcm-experts-digest-additive-manufacturing-2020
https://www.nxtbook.fr/newpress/jeccomposites/jcm2101_138
https://www.nxtbook.fr/newpress/jeccomposites/jcm2011_Special_Issue4
https://www.nxtbook.fr/newpress/jeccomposites/jcm2011_137
https://www.nxtbook.fr/newpress/jeccomposites/jcm2009_136
https://www.nxtbook.fr/newpress/jeccomposites/jcm2007_135
https://www.nxtbook.fr/newpress/jeccomposites/jcm_2020_Q1_Innovation_Report
https://www.nxtbook.fr/newpress/jeccomposites/jcm2005_Special_Issue3
https://www.nxtbook.fr/newpress/jeccomposites/jcm2005_134
https://www.nxtbook.fr/newpress/jeccomposites/jcm2003_133
https://www.nxtbook.fr/newpress/jeccomposites/jcm2001_132
https://www.nxtbook.fr/newpress/jeccomposites/jcm1911_Special_Issue2
https://www.nxtbook.fr/newpress/jeccomposites/jcm1911_131
https://www.nxtbook.fr/newpress/jeccomposites/jcm1909_130
https://www.nxtbook.fr/newpress/jeccomposites/jcm1907_129
https://www.nxtbook.fr/newpress/jeccomposites/jcm1905_128
https://www.nxtbook.fr/newpress/jeccomposites/jcm1903_Special_Issue1
https://www.nxtbook.fr/newpress/jeccomposites/jcm1903_127
https://www.nxtbook.fr/newpress/jeccomposites/jcm1901_126
https://www.nxtbook.fr/newpress/jeccomposites/jcm1811_125
https://www.nxtbook.fr/newpress/jeccomposites/jcm1810_124
https://www.nxtbook.fr/newpress/jeccomposites/jcm1808_123
https://www.nxtbook.fr/newpress/jeccomposites/jcm1807_122
https://www.nxtbook.fr/newpress/jeccomposites/jcm1805_121
https://www.nxtbook.fr/newpress/jeccomposites/jcm1804_120
https://www.nxtbook.fr/newpress/jeccomposites/jcm1803_119
https://www.nxtbook.fr/newpress/jeccomposites/jcm1802_119-Supplement_Innovation_Report
https://www.nxtbook.fr/newpress/jeccomposites/jcm1801_118
https://www.nxtbook.fr/newpress/jeccomposites/jcm1711_117
https://www.nxtbook.fr/newpress/jeccomposites/jcm1710_116
https://www.nxtbook.fr/newpress/jeccomposites/jcm1708_115
https://www.nxtbook.fr/newpress/jeccomposites/jcm1707_114
https://www.nxtbook.fr/newpress/jeccomposites/jcm1706_113
https://www.nxtbook.fr/newpress/jeccomposites/jcm1704_112
https://www.nxtbook.fr/newpress/jeccomposites/jcm1703_111
https://www.nxtbook.fr/newpress/jeccomposites/jcm1701_110
https://www.nxtbook.fr/newpress/jeccomposites/jcm1611_109
https://www.nxtbook.fr/newpress/jeccomposites/jcm1610_108
https://www.nxtbook.fr/newpress/jeccomposites/jcm1608_107
https://www.nxtbook.fr/newpress/jeccomposites/jcm1607_106
https://www.nxtbook.fr/newpress/jeccomposites/jcm1605_105
https://www.nxtbook.fr/newpress/jeccomposites/jcm1604_104
https://www.nxtbook.fr/newpress/jeccomposites/jcm1603_103
https://www.nxtbook.fr/newpress/jeccomposites/jcm1601_102
https://www.nxtbook.fr/newpress/jeccomposites/jcm1511_101
https://www.nxtbook.fr/newpress/jeccomposites/jcm1510_100
https://www.nxtbook.fr/newpress/jeccomposites/jcm1509_99
https://www.nxtbook.fr/newpress/jeccomposites/jcm1507_98
https://www.nxtbook.fr/newpress/jeccomposites/jcm1505_97
https://www.nxtbook.fr/newpress/jeccomposites/jcm1504_96
https://www.nxtbook.com/newpress/jeccomposites/jcm1503_95
https://www.nxtbook.com/newpress/jeccomposites/jcm1501_94
https://www.nxtbook.com/newpress/jeccomposites/jcm1412_93
https://www.nxtbook.com/newpress/jeccomposites/jcm1410_92
https://www.nxtbook.com/newpress/jeccomposites/jcm1409_91
https://www.nxtbook.com/newpress/jeccomposites/jcm1406_90
https://www.nxtbook.com/newpress/jeccomposites/jcm1405_89
https://www.nxtbook.com/newpress/jeccomposites/jcm1404_88
https://www.nxtbook.com/newpress/jeccomposites/jcm1403_87
https://www.nxtbook.com/newpress/jeccomposites/jcm1401_86
https://www.nxtbook.com/newpress/jeccomposites/jcm1311_85
https://www.nxtbook.com/newpress/jeccomposites/jcm1310_84
https://www.nxtbook.com/newpress/jeccomposites/jcm1308_83
https://www.nxtbook.com/newpress/jeccomposites/jcm1307_82
https://www.nxtbook.com/newpress/jeccomposites/jcm1305_81
https://www.nxtbook.com/newpress/jeccomposites/jcm1304_80
https://www.nxtbook.com/newpress/jeccomposites/jcm1303_79
https://www.nxtbook.com/newpress/jeccomposites/jcm1301_78
https://www.nxtbook.com/newpress/jeccomposites/jcm1212_77
https://www.nxtbook.com/newpress/jeccomposites/jcm1210_76
https://www.nxtbook.com/newpress/jeccomposites/jcm1208_75
https://www.nxtbook.com/newpress/jeccomposites/jcm1207_74
https://www.nxtbook.com/newpress/jeccomposites/jcm1206_73
https://www.nxtbook.com/newpress/jeccomposites/jcm1204_72
https://www.nxtbook.com/newpress/jeccomposites/jcm1203_71
https://www.nxtbook.com/newpress/jeccomposites/jcm1201_70
https://www.nxtbook.com/newpress/jeccomposites/jcm1111_69
https://www.nxtbook.com/newpress/jeccomposites/jcm1110_68
https://www.nxtbook.com/newpress/jeccomposites/jcm1108_67
https://www.nxtbook.com/newpress/jeccomposites/jcm1107_66
https://www.nxtbook.com/newpress/jeccomposites/jcm1105_65
https://www.nxtbook.com/newpress/jeccomposites/jcm1104_64
https://www.nxtbook.com/newpress/jeccomposites/jcm1103_63
https://www.nxtbook.com/newpress/jeccomposites/jcm1101_62
https://www.nxtbook.com/newpress/jeccomposites/jcm1011_61
https://www.nxtbook.com/newpress/jeccomposites/jcm1010_60
https://www.nxtbook.com/newpress/jeccomposites/jcm1009_59
https://www.nxtbook.com/newpress/jeccomposites/jcm1006_58
https://www.nxtbook.com/newpress/jeccomposites/jcm1005_57
https://www.nxtbook.com/newpress/jeccomposites/jcm1004_56
https://www.nxtbook.com/newpress/jeccomposites/jcm1003_55
https://www.nxtbook.com/newpress/jeccomposites/jcm1001_54
https://www.nxtbook.com/newpress/jeccomposites/jcm0911_53
https://www.nxtbook.com/newpress/jeccomposites/jcm0910_52
https://www.nxtbook.com/newpress/jeccomposites/jcm0909_51
https://www.nxtbook.com/newpress/jeccomposites/jcm0907-08_50
https://www.nxtbook.com/newpress/jeccomposites/jcm0906_49
https://www.nxtbook.com/newpress/jeccomposites/jcm0904_48
https://www.nxtbook.com/newpress/jeccomposites/jcm0903_47
https://www.nxtbook.com/newpress/jeccomposites/jcm0901_46
https://www.nxtbook.com/newpress/jeccomposites/jcm0811_45
https://www.nxtbook.com/newpress/jeccomposites/jcm0810_44
https://www.nxtbook.com/newpress/jeccomposites/jcm0809_43
https://www.nxtbook.com/newpress/jeccomposites/jcm0807_42
https://www.nxtbook.com/newpress/jeccomposites/jcm0806_41
https://www.nxtbook.com/newpress/jeccomposites/jcm0805_40
https://www.nxtbook.com/newpress/jeccomposites/jcm0803_39
https://www.nxtbook.com/newpress/jeccomposites/jcm0801_38
https://www.nxtbook.com/newpress/jeccomposites/jcm0712_37
https://www.nxtbook.com/newpress/jeccomposites/jcm0710_36
https://www.nxtbook.com/newpress/jeccomposites/jcm0709_35
https://www.nxtbook.com/newpress/jeccomposites/jcm0707_34
https://www.nxtbook.com/newpress/jeccomposites/jcm0706_33
https://www.nxtbookmedia.com