Chemical Engineering October 2015 - 33

Achieve finer PSDs with this
conical mill
The H20 Comil
(photo) is said
to redefine
conical milling
by pushing
the capabilities
of cone
mill technology
toward
finer particlesize
distributions,
making
it ideal for
active pharmaceutical ingredients
(APIs) and fine chemical products.
With its re-engineered drives and
milling efficiency improvements,
the H20 provides superior performance
over jet mills, pin mills or
hammer mills without the need for
expensive additional containment
or air-handling systems, says the
company. The system achieves
30-70% finer particle-size distributions
(PSDs) than traditional conical
mills, and has the ability to control
Quadro Engineering
and shift PSD targets for coarser or
finer results, says the manufacturer.
- Quadro Engineering Corp., Waterloo,
Ont., Canada
www.quadro.com
Two mills in
3276 Bionomic 2c ad_Layout 1 3/8/12 8:31 AM Page 1
one laboratory device
This company has built its first
combination mill comprised of an
S1 batch mill combined with an
SDM-05 mill designed to operate
as a bead mill. Being able to process
both fine and coarse materials
without purchasing two complete
mills to accomplish this, the
S1/SDM-05 combination laboratory
mill provides the option to run
at slower speeds (approximately
100 to 500 rpm) and uses media
ranging from 1/8 to 3/8 in. The
SDM option runs at higher speeds
(approximately 300 to 2,000 rpm).
The system utilizes grinding media
as small as 0.25 mm, and as large
as 2 mm. - Union Process, Inc.,
Akron, Ohio
www.unionprocess.com
Cut Costs & Improve Performance
...with Bionomic Advanced Gas Absorption,
Particulate Capture, Product, and Heat
Recovery Technologies
If you're looking to meet MACT requirements, PM 10 and 2.5
particulate standards, remove odors or mists, abate hundreds
of hazardous and toxic compound emissions, economically
reduce abatement costs through product recovery of specific
compounds, or save energy from a multitude of gas sources,
choose an industry leader who has done it all.
For more than 30 years, Bionomic has partnered with
hundreds of companies globally to design, manufacture,
install and test clean air, product
and heat recovery systems across
a wide range of industries
and applications.
Scan to See
APP photos
Rotor mills with variable speed
and large sample volumes
The new generation of rotor mills
SR 300 and SK 300 has been
greatly improved with regard to
performance, handling and flexibility,
says the manufacturer. The
speed of the rotor beater mill SR
300 has been substantially increased
and can be set between
3,000 and 10,000 revolutions per
minute (rpm), thus allowing for optimum
adaptation to application
requirements. It is therefore ideally
suited for use in pharmaceutical
and food laboratories. The new
cross beater mill SK 300 now also
operates with higher speed, which
can be set from 2,000 to 4,000
rpm. Both mills can be equipped
with an optional cyclone, which
improves material discharge, particularly
for very fine particle sizes,
and provides additional cooling
of the sample. - Retsch GmbH,
Haan, Germany
www.retsch.com
n
Gerald Ondrey
To learn more, call toll free:
800-311-6767, e-mail:
sales@bionomicind.com,
or visit www.bionomicind.com
Circle 3 on p. 102 or go to adlinks.chemengonline.com/56202-03
Circle 23 on p. 102 or go to adlinks.chemengonline.com/56202-23
ChemiCal engineering www.Chemengonline.Com oCtober 2015
33
http://www.quadro.com http://www.retsch.com http://www.unionprocess.com http://www.bionomicind.com http://adlinks.chemengonline.com/56202-03 http://adlinks.chemengonline.com/56202-23 http://www.Chemengonline.Com
Chemical Engineering October 2015

Table of Contents for the Digital Edition of Chemical Engineering October 2015
