S-Diamonds for Crown Preparations S-Diamonds for Cavity Preparations Instruments with a working part length of 6 mm Instruments with a working part length of 9 mm S6801.314.012 S6830RL.314.012 Cylinder with rounded edges Tapered chamfer with modified tip S6801.314.014 S6830RL.314.014 Cylinder round S6836KR.314.012 S6880.314.012 S6979K.314.018 S6801.314.016 S6830RL.314.016 S6836KR.314.014 S6880.314.014 S6886K.314.018 S6801.314.018 S6830RL.314.018 S6836KR.314.016 S6880.314.016 Instruments with a working part length of 10 mm Cylinder round Torpedo Torpedo S6801.314.023 S6830L.314.012 S6835KR.314.012 S6835KR.314.014 S6877.314.012 S6882.314.012 S6879.314.012 S6830L.314.014 S6877.314.014 S6882.314.014 S6879.314.014 S6830L.315.014 S6877.314.016 S6882.314.016 S6879.314.016 S6830L.314.016 S6845KR.314.018 S6830L.314.018 S6845KR.314.025 Instruments with a working part length of 8 mm Cylinder with rounded edges Cylinder round Tapered round Tapered with rounded edges Material reduction in % S6850.314.014 S6848KR.314.014 120 100 S6837KR.314.012 S6881.314.012 S6850.314.016 S6848KR.314.016 S6837KR.314.014 S6881.314.014 S6850.314.018 S6848KR.314.018 S6837KR.314.016 S6881.314.016 Tapered with rounded edges 118% 115% 100 % 80 60 40 Torpedo Flame 20 S6879K.314.014 S6863.314.012 S6878.314.012 S6847KR.314.014 S6879K.314.016 S6863.314.014 S6878.314.014 S6847KR.314.016 S6879K.314.018 S6863.314.016 S6878.314.016 S6847KR.314.018 S6879K.314.021 Tapered round 0 Conventional diamond instruments (various shapes) S-diamond Torpedo tapered S6856.314.012 S6878K.314.012 S6856.314.014 S6878K.314.014 S6856.314.016 S6878K.314.016 S6856.314.018 S6878K.314.018 S6856.314.021 S6878K.314.021 Instruments with a working part length of 12 mm Cylinder round S6882L.314.014 Recommendations for use: * The use in the red contra-angle is recommended, at an optimum speed of (160.000 rpm. Occlusal/lingual reduction Egg Bud S6379.314.018 S6368.314.016 S6862.314.012 S6379.314.023 S6368.314.023 S6862.314.014 S6379.314.029 Flame © 02/2018 · 419123V0 Torpedo tapered * Due to the instruments' high cutting ability, only apply low contact pressure not exceeding 2N. German patent DE 199 08 507 European patent EP 1 031 325 S6862.314.016 www.kometdental.de * Make sure to use sufficient spray cooling (at least 50 ml/min.). SAVE Prices start from $45.73 Henry Schein% Halas · 44 O'DeaPack Avenue · of Waterloo 5 NSW 2017 · Ph 1300 65 88 22 · Fax 1300 65 88 10 · info@henryschein.com.au · www.henryschein.com.au 15 Henry Schein Shalfoon · 23 William Pickering Drive · Albany, North Shore · Auckland · Ph +64 9 414 0040 · Fax +64 9 414 0041 · info@henryschein.co.nz · www.henryscheinshalfoon.co.nz 419123V0_AZ_HenrySchein_SDia_A4_2s.indd 2 15.02.18 09:02 Orders 1 3 0 0 6 5 8 8 2 2 19